Spacecraft MOSFET Circuit Tolerates Radiation-Driven Threshold Shift in Simulation
- Brian Dipert
- 310 reads
After testing found a 45% MOSFET threshold-voltage drop above 50 rad(Si)/s, PSpice simulations showed the converter still regulated its three outputs.


A spacecraft power converter continued to regulate its outputs in simulation after testing found that its MOSFETs could suffer a substantial threshold-voltage shift under high-dose-rate radiation. The result gives a useful distinction for this design: a parameter change that threatens device performance in some circuits may be tolerable when the transistors are used as switches.
Converter architecture and isolation
The power supply is designed for a spacecraft operating in Jupiter’s high-radiation environment. It takes a nominal 28 V input and produces +5 V, +3.3 V, and −5 V rails for onboard sensors. The design uses two IRHNJ57024 N-channel MOSFETs; the radiation-hardened version identified for the device is the JANSR2N7480U3.

Figure 1. Block diagram of the spacecraft power supply for a high-radiation environment.
In the main conversion stage, a PWM controller drives the two MOSFETs through a gate-drive transformer. The switches control energy delivered to transformer T1501, which supplies the load. The drive transformer provides galvanic isolation between the controller and switching stage, helping protect the input-side circuitry if a power-stage fault occurs.
When the MOSFETs turn off, energy held in T1501’s leakage inductances is recovered and returned to the DC-link buffer capacitors. That energy-recovery path improves converter efficiency. The power ground, NIM_PGND, is also isolated from the PWM ground, DGND_DPU. This separation helps keep switching-stage spikes and noise from disturbing the controller circuitry.

Figure 2. Schematic of the power supply’s primary conversion stage.
Fast switching currents interacting with parasitic inductance can create high-amplitude spikes on the power ground. The design uses snubbers, optimized from measurements, to reduce the effects of transformer leakage inductance and parasitic capacitance. The controller’s voltage-feedback input, VFB, regulates the output voltage, while its current-sense input, ISEN, supports current limiting. A signal named RAMP_NIM2, proportional to total output current, is fed back to the PWM controller.
Radiation test result and circuit response
Additional MOSFET testing after launch identified sensitivity in the manufacturing lot used in the converter. Degradation appeared when the high-dose-rate (HDR) exposure exceeded 50 rad(Si)/s, despite a stated qualification for total ionizing dose (TID) up to 100 krad(Si). These figures describe different radiation conditions: the finding concerns the rate of exposure, while the TID rating describes accumulated dose.
The reported HDR effect was an approximately 45% reduction in MOSFET threshold voltage, Vth. The datasheet gives a VGS(th) range of 2.0 to 4.0 V. At the 2.0 V lower end, a 45% reduction would bring the threshold to approximately 1.1 V. That shift warranted checking how the altered device parameter would affect switching and the converter’s output regulation.
The circuit was evaluated in PSpice with the MOSFET VGS(th) parameter varied across a wide range, down to 0.5 V. At that simulated value, the +5 V, +3.3 V, and −5 V outputs remained nominal, and the plotted MOSFET gate voltages were used to assess switching behavior.

Figure 3. PSpice results at VGS(th) = 0.5 V show nominal output rails above and MOSFET gate voltages below.
Why the operating mode matters
The simulation indicates that this converter can keep operating with a much lower threshold voltage than the nominal device value. In this circuit, the MOSFETs act as switches: the key question is whether the drive and switching behavior still support conversion and regulation as the threshold shifts. The modeled results show that they do, even at 0.5 V.
That outcome should be read in the context of this circuit and its simulation. Threshold voltage can have a different effect when a MOSFET is used in a linear application, where the device operates between fully on and fully off. The reported result therefore does not establish that the same radiation-induced shift is harmless in other circuits or operating conditions.
The practical engineering takeaway is that a radiation test result needs to be evaluated against the transistor’s role in the actual design. Here, the measured concern led to a circuit-level simulation sweep, which showed continued regulation across the modeled threshold range. The work was described by Janos Nagy, a senior electronics engineer specializing in scientific instrumentation, embedded systems, power electronics, and space hardware.