Skip to the stories
Electronics & Semiconductors

NETGEAR CM1000 DOCSIS 3.1 Modem Teardown Reveals Broadcom SoC and RF Components

  • Brian Dipert
  • 495 reads

A CM1000 v2 teardown identifies its DOCSIS 3.1 SoC, memory, RF amplifier and switch, while showing how heatsinks and shielding divide the board.

NETGEAR CM1000 DOCSIS 3.1 Modem Teardown Reveals Broadcom SoC and RF Components

The NETGEAR CM1000’s most consequential parts sit beneath its heatsinks and a shielded RF section: a Broadcom BCM3390 DOCSIS 3.1 system-on-chip, a programmable-gain amplifier, an RF switch and separate memory devices. A teardown of a used CM1000 v2 traces those components across both sides of the PCB and exposes the cooling and shielding choices around them.

Two versions, one unexpected teardown

The CM1000 shares its basic appearance with NETGEAR’s CM1100, but the CM1000 has one RJ45 LAN port and lacks the second LAN status LED. The CM1100 has two LAN connections, though the author says the service provider did not allow the second port to be enabled on his unit. That made a CM1000 the more practical candidate for disassembly than either of his working CM1100 modems.

There are two CM1000 hardware versions, v1 and v2, but the available descriptions offered little detail beyond references to “slight hardware changes.” The teardown was intended to compare both versions. A unit bought as a v1 based on its listing photos turned out to be a v2; the seller had not explicitly identified it as v1, and the return window had closed before the mismatch was discovered. A second, untested v2 was kept intact as a possible spare, while another purported v1 was on order for a later comparison.

The modem opened here was described as malfunctioning and arrived without a power supply. Its reported symptom was random reboots every few minutes, though the teardown does not establish whether that fault was present or what caused it. The intact, untested unit came with a power supply, which was photographed but left unopened.

Opening the enclosure

From the outside, the author documented the front, sides, rear, top and base before opening the enclosure. One screw secures the base. Removing it exposes the interior; two more screws at the back and several clips then allow the enclosure halves to separate. Light pipes inside the case carry the PCB’s LED output to the front indicators.

Two additional screws hold the board in place. Once removed, the PCB lifts free, revealing heatsinks on both sides. That layout matters: examining only one face gives an incomplete view of what the thermal hardware is serving. In particular, a large heatsink on one side sits opposite a shielded area on the other.

Memory and cooling on the first side

A small silver heatsink near the top of one PCB face covers a Macronix MX30LF1G18AC, a 1 Gbit SLC NAND flash memory. The package markings were faint after the thermal paste was cleaned away, so the identification is based on the remaining markings. The author suggests the device holds system firmware.

A larger black heatsink sits lower on the same side. Little is visible beneath it from that face, but the corresponding area on the reverse contains heat generating components. The arrangement suggests the heatsink transfers heat across the board, though the author describes that thermal contact as imperfect. The teardown does not include temperature measurements or a thermal performance assessment.

The DOCSIS processor and shielded RF section

On the opposite face, a larger black heatsink covers Broadcom’s BCM3390 DOCSIS 3.1 SoC. Nearby, a substantial Faraday cage encloses a collection of integrated circuits and discrete RF components. Removing the cage reveals a dense assembly of surface mount capacitors, inductors, resistors, transformers and transistors.

The largest chip in the exposed section is Analog Devices’ MAX3522B, a DOCSIS 3.1 programmable-gain amplifier. A copper colored thermal pad on the reverse side lines up with the amplifier area, connecting the component placement to the heatsink seen on the other face. To the amplifier’s right is a pSemi PE42722 single-pole, double-throw RF switch.

Another chip in the shielded area carries the markings “3432,” “KMLG 10,” “EE1852” and “0403 W”; its identity remains unresolved. The board’s RF section is therefore only partly identified, but the marked components show how much of the modem’s signal path is concentrated beneath the shielding.

Memory and Ethernet interface

Outside the shielded section, an ESMT M15T1G1664A provides 1 Gbit of DDR3(L) SDRAM. An unpopulated footprint sits above it, although the teardown does not determine its intended use or whether it relates to another configuration.

Beside the BCM3390, near the RJ45 connector, is a Bothhand GST5009 LF surface mount 1000BASE-T magnetic module and pulse transformer. Its position places the Ethernet interface components close to the modem’s single LAN port.

This teardown maps the major identified devices in the CM1000 v2 and shows how the enclosure, heatsinks and shield divide its circuitry. The planned v1 examination should help establish whether the two versions differ in parts, layout or both; the v2 board alone cannot resolve those changes.

Source: Brian Dipert · www.edn.com

From the same set