Fibocom Tests LTE Cat.1 bis Modules on Starlink Direct-to-Cell Network
- IoT.Business.News
- 927 reads
Fibocom’s New Zealand tests connected two LTE modules to Starlink satellites, while showing lower indoor performance and higher energy use.



Connecting an IoT device through a satellite link may not require a separate satellite modem in every design. Fibocom reports that its LE270-EU and LE271-GL LTE Cat.1 bis modules established IP data sessions on SpaceX’s Starlink Direct-to-Cell (DTC) network during field tests in New Zealand. The modules used standard firmware and required no satellite-specific hardware modifications.
That result offers a practical route to extending cellular devices beyond terrestrial coverage, but it doesn’t make satellite operation equivalent to a nearby cellular base station. Fibocom’s measurements show how sky visibility affects throughput and response rates, and how satellite data transfers can increase energy use. Those factors will shape whether an existing device design can support useful service in the field.
Existing LTE modules make the connection
Starlink DTC places LTE base station capabilities on low Earth orbit satellites. Compatible cellular devices can then communicate through the satellite network when terrestrial base stations are out of reach, using participating mobile operators.
In Fibocom’s demonstration, both modules connected to the live network and exchanged data using their ordinary LTE module hardware. That matters to product teams because it suggests a possible way to add satellite coverage while retaining much of an existing device’s communications design. Avoiding a dedicated satellite modem could reduce hardware changes and development work, though the tests don’t quantify any cost savings.
Module capability alone doesn’t settle whether a product can use a particular DTC service. Network access arrangements, device eligibility and performance in the intended installation all need consideration. The demonstration also doesn’t establish compatibility with other satellite networks or prove how the modules will behave at commercial scale.
Sky visibility shapes data performance
Fibocom tested outdoors, in a vehicle and indoors, examining operation under differing satellite visibility conditions. Under good sky visibility, the LE270-EU reached approximately 2.2 Mbps downlink throughput, while the LE271-GL reached 2.0 Mbps. Both delivered around 0.3 Mbps uplink throughput.
Network registration took approximately 1 to 30 seconds. In favorable conditions, ping response rates reached 80% to 90%. Those figures describe the tested conditions; they shouldn’t be treated as a guaranteed service level for every location, device orientation or network situation.
When buildings or other obstructions limited visibility, performance fell. In some hotel-room scenarios, downlink throughput dropped to approximately 0.5 Mbps, and ping response rates were around 65% to 70%. Some requests also took substantially longer to return. The gap between favorable outdoor results and indoor measurements is a reminder that installation context can matter as much as the module’s nominal cellular category.
For asset tracking, a module mounted inside a vehicle or container may not see the sky as clearly as a device installed outdoors. Agricultural sensors and remote infrastructure equipment can face their own obstructions depending on placement. Teams evaluating these systems will need to consider where devices sit and how often they need to report. For low-volume sensing, dependable delivery of short messages may be more useful than peak throughput.
Satellite transfers affect the energy budget
Fibocom also compared the energy needed to upload the same file over satellite and terrestrial cellular connections. The satellite transfer used approximately 1.5 to 1.8 times as much energy, according to the company. Longer transmission times, higher transmission currents and retransmissions contributed to the increase.
For a battery-powered product, that difference can affect service life even if the module’s standby behavior remains unchanged. Fibocom says the LE270 and LE271 families support Power Saving Mode (PSM) currents as low as 2.5 μA, and reports that low sleep current was maintained during testing. Its results point to active satellite communication, rather than standby operation, as the main source of additional energy demand in the measured transfers.
Device designers may be able to manage that demand by sending data less often, storing readings until a suitable transmission opportunity, or adjusting retries to changing link conditions. The right balance depends on how quickly an application needs to receive data and how much uncertainty it can tolerate. A design that works well with frequent terrestrial updates may need a different reporting schedule when it relies on a satellite connection.
A useful step toward hybrid coverage
The tests add evidence that established LTE hardware can communicate over a direct-to-cell satellite network. For products that need coverage beyond terrestrial networks, this could make a hybrid design easier to consider without building a separate satellite radio into every device.
Still, the New Zealand demonstration leaves important engineering questions open. The results don’t cover every deployment environment, satellite network or large-scale operating condition. Fibocom says it is continuing to optimize DTC firmware compatibility for the LE270 and LE271 series, with attention to registration efficiency and connection resilience.
For IoT developers, the practical takeaway is that satellite access may fit within a conventional LTE module design, but it brings its own link and power constraints. Before settling on a product configuration, teams will need to assess coverage at the device’s installed location, required message delivery and battery budget together.